Product
High-speed autofocus system
Classification:
Detail
Parameters
Technical Data
Characteristics
● Z-axis dynamic scanning, driven by a voice coil motor
● Provides a variable focus for the scanning system
● Can operate continuously at frequencies up to 175 Hz (for more information, see the Operating Range Curve tab)
● Available in a non-contact air-bearing version or a lubricated, air‑free version
● Servo drive included
● Power supply, command interface cable, power cord, and servo drive installation

High-speed autofocus system
● Dynamic Z-axis Scanning
● Provides a variable focus for the scanning system
● Non-contact air bearing
● Pressure switch assembly included
The BLINK high-speed focus adjuster (U.S. Patents 10,500,676 and 11,090,761) enables high‑frequency, high‑precision linear displacement, thereby dynamically adjusting the laser beam’s focal point. As part of a galvanometer scanning system, it can fine‑tune the system’s effective focal plane, allowing the output spot to accommodate large angles or arbitrary surface geometries. When used as the focusing element in a post‑objective scanning system, the BLINK also supports high‑speed processing of large‑area samples and 3D‑profile specimens. We offer versions with or without an adhesive‑bonded lens; the lens‑equipped version is compatible with Nd:YAG or 355 nm lasers. Operation of these focus adjusters requires a compressed air supply rated at Class 3 cleanliness and 60–90 psi pressure. For further details, please refer to… Specifications Tag.
BLINK combines air‑bearing guides with direct voice‑coil actuation to deliver a highly compact, high‑performance focuser. Operable continuously under 175 Hz sinusoidal drive, its ultra‑low moving mass minimizes reaction forces. Featuring only a single moving component, BLINK offers superior reliability and extended service life compared with conventional tension‑belt actuators.
The focuser housing features two through-holes for mounting 1/4"-20 (M6) socket-head cap screws. The base of the device is equipped with four M3 threaded mounting holes—two on the black bracket and two on the cylindrical lens housing. Around the optical port, there are four M3 threaded holes spaced 0.92" apart, enabling custom mounting options.
Airless high-speed autofocus unit
● Dynamic Z-axis Scanning
● Provides a variable focus for the scanning system
● Lubricated bearings do not require pressurized air.
The BLINKL air‑free high‑speed focus adjuster achieves high‑frequency, high‑precision linear displacement without requiring an external pressurized gas supply, thereby dynamically repositioning the laser beam’s focal point. When integrated into a galvanometer‑based scanning system, it can fine‑tune the system’s effective focal plane, compensating for large‑angle scanning or accommodating output surfaces of arbitrary shapes. As a focusing element in post‑objective scanning systems, the BLINKL focus adjuster also enables high‑speed processing of large planar samples and three‑dimensional profiled specimens. The device is available with either adhesive‑free optics or adhesive‑mounted lenses optimized for Nd:YAG or 355 nm lasers.
The BLINKL air‑free focuser combines a lubricated linear guide—requiring no pressurized air supply—with direct voice‑coil actuation, resulting in an exceptionally compact and high‑performance focusing system. The BLINKL can operate continuously under 175 Hz sinusoidal drive, and its ultra‑low moving mass minimizes reaction forces. Featuring only a single moving component, the BLINKL focuser offers superior reliability and extended service life compared with conventional tension‑belt actuators.
The focuser housing features two through-holes for mounting 1/4"-20 (M6) cap screws. The device’s base is equipped with four M3 threaded mounting holes—two on the black bracket and two on the cylindrical lens housing. Around the optical port, there are four M3 threaded holes spaced 0.92" apart, enabling custom mounting options.
Open‑type linear power supply and command interface cable
● GPWR15 Power Supply: A ±15 V power supply for single‑axis and dual‑axis systems; a single unit can power up to two galvanometer scanners.
● BLINK(L) Focuser
● QS, SS, and SP Series VantagePro® Galvanometer Scanners
● GRS8-AG Resonance Scanner
● XG Series Scan Head
● GPWR15 Power Supply Specifications
● The open-frame design requires welding of the cables.
● Input: 100–120 or 220–240 VAC
● Output: ±15 V @ 5 A (maximum power 150 W)
● Operating temperature: 0 - 50 °C
● Dimensions: 14.0 inches x 4.9 inches x 3.5 inches (356 mm x 124 mm x 90 mm)
● CBLS2F: Command interface cable with power cord, for QS7 and QS10 series galvanometer scanners and BLINK(L) high-speed focusers.
The GPWR15 is a low-noise linear power supply designed to minimize electrical interference and achieve the highest system resolution. Compatible systems include the BLINK(L) focusers, XG‑series scan heads, GRS8‑AG resonant scanners, and QS, SS, and SP series galvanometer scanners. This power supply delivers 5 A at ±15 VDC and can be configured to accept mains voltages of 100–120 VAC or 220–240 VAC. It features an open-frame design, allowing users to solder compatible power cables directly into their system.
The CBLS2F command‑interface cable and power cord enable the GPWR15 power supply to be connected to the BLINK(L) high‑speed focuser or to QS7 and QS10 series galvanometer scanners. One end of the power cord features a 4‑pin connector compatible with BLINK focusers, while the other end consists of three bare wires for soldering to the GPWR15 power supply. The command‑interface cable has a 2‑pin connector at one end, also compatible with BLINK focusers, and three bare wires at the other end for connection to a user‑provided controller.
Closed-loop linear power supply and composite cable
● GPS011 Series: ±15 V power supplies for single‑axis and dual‑axis systems; a single power supply can power up to two galvanometers.
● BLINK(L) Autofocus Device
● QS7, QS10, QS15, and QS20 Series VantagePro® Galvanometer Scanners
● GRS8-AG Resonance Scanner
● XG Series Scan Head
● GPS011 Power Supply Specifications
● Closed-type enclosure, allowing direct cable connection to the system.
● Input: 100 VAC / 50 or 60 Hz, 115 VAC / 60 Hz, 230 VAC / 50 Hz
● Output: ±15 VDC @ 3 A
● Operating temperature: 5 - 40 °C
● Dimensions: 7.05 inches x 10.79 inches x 4.8 inches (179 mm x 274 mm (Max) x 122 mm)
● CBLS2P: Command interface cable and power cord, for the BLINK(L) high-speed focuser and QS7/10 scanning galvanometer system.
The GPS011 series power supplies are low-noise linear sources designed to minimize electrical interference, enabling the highest resolution in both one‑dimensional and two‑dimensional galvanometer‑based scanning systems. Compatible systems include the BLINK(L) focusers, the QS7, QS10, QS15, and QS20 series galvanometer scanners, the GRS8‑AG resonant scanner, and the XG series scan heads. These power supplies deliver 3 A at ±15 VDC and can be configured to accept mains voltages of 115 VAC (model GPS011‑US), 230 VAC (model GPS011‑EC), or 100 VAC (model GPS011‑JP). The GPS011 units are enclosed and feature direct connection to compatible power cords, eliminating the need for soldering.
Please note that the GPS011 series power supply is insufficient to drive the QS30/45 scanning galvanometer system.
The CBLS2P command‑interface cable and power‑supply cord combination enables the GPS011 series galvanometer‑system linear power supply to be connected to the BLINK(L) high‑speed focuser or to QS7 or QS10 series galvanometer scanners. The power‑supply cord features a three‑pin circular connector at one end, compatible with GPS011 series power supplies, and a four‑pin connector at the other end, compatible with BLINK(L) focusers and QS7 and QS10 galvanometers. The command‑interface cable has a BNC connector at one end, compatible with user‑provided controllers, and a two‑pin connector at the other end, compatible with BLINK(L) focusers and QS7/10 galvanometers.
Heatsink and mounting bracket for the servo driver of a high-speed focuser
● The mounting base is compatible with the high-speed focuser’s servo drive (available separately).
● Passive air-cooled heatsink
● The removable aluminum cap features an opening for attaching a focuser.
● Mounted on a standard breadboard or optical table via two slots
The Chongfan Technology QDM1 mounting bracket provides a convenient installation solution for the servo driver of the front‑mounted high‑speed focuser. This bracket features two slots and can be secured to a standard breadboard or optical table using 1/4" (M6) cap screws. The servo driver is mounted to the bracket with the two included 4‑40 screws. On the back, the QDM1 bracket serves as an integrated passive air‑cooled heat sink, enhancing thermal dissipation. For applications that generate significant heat or demand high stability, the bracket should be attached to a larger heat‑sinking base—such as an optical table or breadboard—to optimize thermal resistance. The bracket also includes a removable aluminum cover, with openings that allow connection to compatible servo drivers.
Previous
Previous
Other Products
I want to consult