All Categories >

Product

+
  • f926bced-9a91-468a-a524-d2519afde178.png
  • 87f14849-e8f7-491b-8dd9-61eb0726eaa2.png

Picosecond and nanosecond lasers with tunable gain

Picosecond and nanosecond lasers with tunable gain; center wavelengths ranging from 405 to 1550 nm; capable of operating in picosecond pulse, nanosecond pulse, or continuous-wave modes; pulse widths below 130 ps and repetition rates up to 200 MHz; compact laser systems delivering output via single-mode or polarization-maintaining fiber coupling.

Classification:

Detail

Parameters

Technical Data

Picosecond and nanosecond lasers with tunable gain

● Center wavelength from 405 to 1550 nm

● Picosecond pulse, nanosecond pulse, or CW operation

● <130 ps pulse width and a maximum repetition rate of 200 MHz

● Compact laser system with output coupled via single-mode or polarization-maintaining fiber

 

Characteristics

● Short-pulse lasers with center wavelengths ranging from 405 to 1550 nm

● Optional pulse width less than 130 ps, with pulse widths ranging from 1 to 65 ns, or CW operation

● Single-mode or polarization-maintaining fiber-coupled output

● Lasers with a center wavelength ranging from 450 to 1064 nm are supplied with precision fiber optic patch cords.

● Integrated drive and temperature control electronics

● Trigger output for pulse synchronization

● Internal and external triggering from single-shot to 200 MHz

Chongfan Technology’s GSL series of gain‑tunable lasers is a compact, plug‑and‑play single‑mode or polarization‑maintaining fiber‑coupled light source, offering picosecond, nanosecond, and continuous‑wave operation. The gain‑tunable pulse generation feature provides adjustable pulse widths and a repetition rate of up to 200 MHz, making these lasers well suited for high‑speed imaging, fluorescence lifetime measurements, and pulsed‑signal testing. The GSL series lasers also utilize our… Fiber optic amplifier An ideal seed source for further amplification of the series.

The laser diode’s driver electronics and temperature-control circuitry are integrated into each unit and are supplied with the accompanying… DS15 Power is supplied via a power adapter and a plug compatible with local standards. The GSL41A laser features an FC/PC fiber‑pigtail output. Other models in the GSL series provide an FC/APC connector on the front panel. We offer single‑mode, fiber‑coupled GSL lasers in the GSLxxxA format, as well as polarization‑maintaining, fiber‑coupled lasers in the GSLxxxAP format. GSL

The fiber output of this laser series enables their integration into a wide range of fiber‑terminated devices.

Fixed pigtail with end cap

Our 405 nm model, the GSL41A, stands out in this series due to its permanently attached FC/PC fiber pigtail, which features an end cap with a length of 500 ± 50 µm. This end cap expands the beam profile at the fiber‑optic output, thereby reducing the optical power density and preventing material buildup at the air–fiber interface—a phenomenon commonly observed in high‑power near‑UV wavelength fiber‑coupled lasers that can, over time, lead to degradation of the fiber’s performance.

Fiber optic patch cord with precision connectors

GSL-series lasers with a mode field diameter of less than 7 μm (except the GSL41A) are supplied with a precision‑connectorized fiber optic patch cord, available in the following models: GSL45A, GSL45AP, GSL49A, GSL52A, GSL52AP, GSL63A, GSL64AP, GSL79AP, GSL85A, GSL85AP, GSL92A, GSL106A, and GSL106AP. For more details, please refer to the labels on the precision fiber optic patch cords.

Collimator Recommendation

If you need to collimate the output beam of a GSL-series laser, we recommend using CFC Series Adjustable Aspheric Fiber Optic Collimator 。

Pulse width and repetition rate control

Each GSL‑series laser offers pulse‑width control that allows switching between picosecond operation (<130 ps), nanosecond operation with 14 discrete settings (1–65 ns or 2–65 ns), and continuous‑wave operation. Single‑shot mode is also available for pulse widths ≥6 ns. Pulse‑width control is located on the rear panel, enabling direct programming of the pulse generator; an included 2.5 mm screwdriver can be used to adjust it to one of 16 positions. The specification label provides diagrams illustrating typical pulse waveforms and the relationship between typical pulse widths and corresponding pulse‑width control settings.

In addition to pulse‑width control, the repetition‑rate control offers access to four internal and two external trigger settings, accommodating both Hi‑Z and 50‑Ω impedance connections. The internal repetition rate can be selected among 1 MHz, 10 MHz, 100 MHz, and 200 MHz. Use the included 2.5 mm flat‑head screwdriver to choose the desired trigger setting. Note that for pulse widths exceeding 2 ns, the maximum frequency is below 200 MHz.

 

Trigger

The SMA female trigger input/output port on the rear panel serves a dual purpose. When the internal oscillator is used, the trigger port provides an output signal synchronized with pulse generation. In user-triggered mode, the SMA port supports external trigger sources (such as our…). EPG1 Electrical Pulse Delay Generator ) to control the repetition rate. The Hi-Z and 50 Ω user-triggered modes are suitable for low-frequency and high-frequency operation, respectively.

Other front and rear panel features
The dual-color (red/blue) LED on the front panel indicates when the laser output is enabled and is designed for most… Laser safety goggles All can be seen.

In addition to the trigger port, pulse‑width control, and repetition‑rate control, the multicolor LEDs on the rear panel indicate the operating status, including temperature stability and any error conditions. The rear panel also includes a reference table for repetition‑rate options. For more information on these features, please refer to the front‑ and rear‑panel labels and Manual 。

The GSL series lasers feature built-in safety features, including a key switch, interlock pins, and a four-second delay between LED illumination and laser output.

Electrical connection

Each laser is supplied with a plug and external components suitable for local use. DS15 Power supply. The laser integrates all other drive electronics, safety interlocks, and temperature‑stabilization functions required for operation; for a block diagram with more detailed information, please refer to the specification label.

 1M-class laser sticker   Class 3B laser sticker   Visible laser sticker   Invisible laser sticker  

             

 

Picosecond laser, gain-tunable, single-mode pigtail with end cap, 405 nm

 

● Tunable-gain laser, 450 nm - 1550 nm

● Includes an FC/APC single-mode precision patch cord, suitable for lasers with a center wavelength ≤ 1064 nm.

These GSL-series lasers feature single-mode FC/APC output connectors for mating with fiber optic pigtails. Precision single-mode fiber pigtails spanning a wavelength range from 450 to 1064 nm have cores precisely centered within their tight‑fit ferrules, whose inner diameters are closely matched to the cladding diameter of the connected fibers, thereby minimizing core misalignment and maintaining optimal output power. For additional details, including the mode field diameter of the included precision pigtails, please refer to… Precision fiber optic patch cord Tags. GSL131A and GSL155A do not include fiber optic patch cords.

 

Picosecond laser, gain-tunable, polarization-maintaining fiber, 450–1550 nm

 

● Tunable gain laser, with wavelengths ranging from 450 nm to 1550 nm

● Lasers with a center wavelength ≤ 1064 nm include FC/APC precision fiber optic patch cords.

These GSLxxxAP series lasers deliver polarization‑maintaining output and are equipped with FC/APC fiber connectors for connecting fiber patch cords. Lasers spanning wavelengths from 450 to 1064 nm include precision polarization‑maintaining fiber patch cords, whose fiber cores are highly centered within the ferrule and feature a tightly matched ferrule inner diameter and fiber cladding diameter, thereby minimizing core misalignment and output power loss. For detailed information, please refer to the accompanying documentation. Precision fiber optic patch cord Tags include the mode field diameter of the included precision patch cords. The GSL131AP and GSL155AP lasers do not come with fiber optic patch cords.

Picosecond and nanosecond lasers with tunable gain

Other Products

I want to consult

Submission