Product
High-speed laser power modulator for two-photon microscopy
Classification:
Detail
Parameters
Technical Data
High-speed laser power modulator for two-photon microscopy
● An alternative to Pockels cells and acousto-optic modulators
● Supports a broad wavelength range from 700 nm to 1350 nm
● Light-activated control can reach 500 nJ
● Near-zero dispersion reduces the need for pre-compensation.
Characteristics
- Provides DC power attenuation and high-speed modulation.
- Full extinction AC modulation up to 200 kHz
- Supports region-of-interest selection, edge culling, and frame culling in imaging systems.
- Alternative to the Pockels cell, polarization-independent
- Intelligent electronic drive design delivers smooth optical response and arbitrary trajectory tracking.
- Operating wavelength range: 700 nm – 1100 nm or 700–1350 nm
- On/Off time < 1 μs
- The contrast ratio is as high as 2500:1.
- Compatible with ThorImageLS and ScanImage software®
- Includes a photodetector for monitoring/calibrating the output power.
- Near-zero dispersion (< 100 fs²)
- Passive cooling to eliminate vibration
Chongfan Technology’s high-speed laser power modulators employ deformable mirror technology, enabling rapid intensity modulation and beam attenuation. The all‑reflective design incorporates a gold‑coated MEMS mirror that is polarization‑independent and introduces minimal chromatic dispersion (< 100 fs²). This high‑speed optical modulator is a unidirectional device that accepts collimated input beams with diameters ranging from 1 to 2 mm (1/e²), optical powers up to 10 W, and pulse energies as high as 500 nJ, making it compatible with common 1‑μm wavelength, high‑pulse‑energy lasers. These modulators are available in standard contrast ratios (>250:1) or high contrast ratios (>2500:1), covering operating wavelength ranges of 700–1100 nm or 700–1350 nm (high contrast only).
As shown in Figure 1.1, the transmittance is a function of both the input voltage and the wavelength, and is controlled by an analog input voltage ranging from 0 to 1 V. This voltage can be generated using off-the-shelf data acquisition (DAQ) hardware or other electronic devices. The high-speed optical modulator supports continuous DC operation and modulation frequencies of up to 200 kHz, making it well suited for imaging applications such as flyback blanking or region-of-interest (ROI) selection.
The high contrast ratio of the OM6NH (/M) and OM6ENH (/M) modulators is achieved through two integrated MEMS mirrors; when deformed, these mirrors function as gratings, with one diffracting light in the horizontal direction and the other in the vertical direction, thereby enhancing contrast performance.
Suitable for photoactivation and two-photon fluorescence applications.
This type of modulator is well suited for a wide range of applications, including two-photon fluorescence microscopy and photoactivation. Both techniques require rapid modulation of the laser power of ultrafast near-infrared (NIR) laser pulses to control sample exposure times during imaging and minimize thermally induced damage. Conventional high-speed modulation is typically achieved using bulk‑crystal modulators, such as Pockels cells and acousto‑optic modulators (AOMs). Because these devices rely on bulk materials, they introduce substantial chromatic dispersion, which degrades image quality.
Replaceable photodetector
The internal beam sampler directs a small fraction (< 1%) of the modulated beam to a separate output port, where a photodetector is mounted to monitor the transmission. If necessary, the factory‑installed detector can be removed and replaced with a user‑supplied detector; simply loosen the 8‑32 mounting screw beneath the modulator using a 9/64‑inch hex key. Both the OM6N (/M) and OM6NH (/M) modulators include a… PDA100A2 The detector, OM6ENH(/M) modulator, includes a PDA20C2 Probe.
Housing and Mounting Characteristics
Both the input and output ports of the laser power modulator feature SM05 (0.535”-40) internal threads, enabling the attachment of components with SM05 external threads. Aim at the target or Aperture (Not included.) Moreover, all three ports feature 4-40 tapped holes for compatibility with our… 30 mm cage system . To assist with initial alignment, we recommend using at the modulator input端 SM05 lens tube with groove or 30 mm cage system components.
Using the three slots on the housing to pass through CL6 (Without included) platform clamps allow the modulator to be mounted directly onto an optical table, with a minimum beam height of 1.25 inches. The base also features three 8-32 (M4) mounting holes for additional mounting. Base-mounted extension rod , thereby raising the modulator to the required beam height.
The instrument is shipped with a 24 V power supply featuring a KPJX-4S-S connector (for the modulator) and a ±12 V power supply (for the photodetector). For more details, please refer to the pin‑out diagram.










Previous
Next
Previous
Next
Other Products
I want to consult